COMPONENTS
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE DRIVE BELT
(See REMOVAL )
3. REMOVE NO. 3 TIMING BELT COVER LH (See REMOVAL )
4. REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt, stud bolt and camshaft position sensor.
INSTALLATION
1. INSTALL CAMSHAFT POSITION SENSOR
Install the camshaft position sensor with the bolt and stud bolt Torque: 7.5 N*m (80 kgf*cm, 66 in.*lbf)
2. INSTALL NO. 3 TIMING BELT COVER LH (See INSTALLATION )
3. INSTALL DRIVE BELT
2006 ENGINE PERFORMANCE Engine Control System - Sequoia
(See INSTALLATION )
4. FILL ENGINE COOLANT (See REPLACEMENT )
5. CHECK ENGINE COOLANT FOR LEAKS
6. CHECK IGNITION TIMING
(See ON-VEHICLE INSPECTION )
2006 ELECTRICAL Charging - Sequoia
2006 ELECTRICAL Charging - Sequoia
Continue reading here: Charging System
Was this article helpful?
Asked by jvalencia May 19, 2017 at 10:50 AM about the 2000 Toyota Tundra V8 SR5 2 Door LB 4WD
Question type: Maintenance & Repair
where is the cam sensor located
4 Answers
If the timing belt was just done or is overdue, you may have belt issues. The cam sensor is under the timing cover by the cam. Remove upper plastic timing cover and you will see it. If you wanna test it, minimum resistance is 835 ohms and maximum is 1400 ohms and you measure it with engine cold.
10 people found this helpful.
- Report
what is the procedures to test the camshaft position sensor. have replaced sensor and pu is still having problems. is there something else i need to check
8 people found this helpful.
- Report
camshaft position sensor issue is on a 2001 toyota Tundra 4.7
7 people found this helpful.
just found out today check engine light wouldnt go out with computers for inspection on a 2007 toyota tundra that had cam shaft sensor and crankshaft sensor replaced also couldn't get check engine light off found out today their is 2 camshaft sensors on my 2007 toyota tundra. my suggestion is find out how many sensors you have and replace mine went all at once.
Your Answer:
Related Questions
-
4.7 L engine Cam sensor first bank 4 Answers
where is the cam sensor located
2000 Toyota Tundra V8 SR5 2 Door LB 4WD
-
Maintenance & Repair
-
PO161 oxygen sensor. Bank 2 sensor 2. On a 2000 tundra 4.7 V8 4 Answers
Where is the PO161 sensor located on a 2000 tundra. 4.7 V8
2000 Toyota Tundra
-
Maintenance & Repair
-
replacing 02 sensor Bank 2 #1 in a 2000 V8 4WD Tundra 1 Answer
I am going to attempt this myself, found the sensor, do you have to unhook the battery before you start, or just at the end to clear the codes?
2000 Toyota Tundra V8 SR5 4 Door Extended Cab 4WD
-
Maintenance & Repair
-
Engine 2 Answers
#8 cylinder miss.......replaced plugs, coils, injector, and cam position sensor... Still has a miss. Same as before I started.. I'm at a loss as to what to do next
2000 Toyota Tundra V8 SR5 4 Door Extended Cab RWD
-
Maintenance & Repair
-
Vsc sensor is out just don't know which one is bank 1 Answer
The vsc is out just don't know what side bank 2 rear.
2007 Toyota Tundra 4.7L LB RWD
-
Maintenance & Repair
Looking for a Used Tundra in your area?
CarGurus has 17,195 nationwide Tundra listings starting at $3,000.
Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.