How much does it cost to replace a camshaft actuator

Reading Time: 4 minutes

Nearly all late-model vehicles are equipped with variable valve timing (VVT). The technology can improve engine performance, reduce emissions, increase fuel economy, or all of the above, depending on the system configuration. 

One or more camshaft actuators—also known as camshaft phasers—act as the heart of the VVT system. When conditions are correct, the phasers alter the position of the camshafts to adjust the engine’s valve timing.

Although camshaft phasers sound great in theory, they’re a common failure point on many modern engines. It’s helpful to have a basic understanding of phasers in case you ever need to replace them on your car.

What is a Camshaft Phaser?

Some vehicle manufacturers refer to camshaft actuators as phasers, while others use different terminology. But regardless of what they’re called, all phasers serve the same purpose: adjusting the position or the “phase” of the camshaft in relation to the crankshaft, thereby altering valve timing.

To understand the concept better, it helps to first understand camshafts, valves, and variable valve timing.

How the Camshafts and Valves Work

Inside the engine, there’s a crankshaft and one or more camshafts. The camshafts open and close a series of valves that allow air (and fuel, in the case of port injection) into the engine and exhaust gases out.

Meanwhile, the crankshaft is attached to the connecting rods and pistons. When the vehicle is running, the valves allow air to enter the engine’s cylinders and mix with fuel. The mixture is ignited by the spark plugs, creating a series of small explosions. Each explosion forces one of the pistons downward inside the engine.

The movement of the pistons makes the crankshaft turn, creating the rotational force needed to propel your vehicle down the road. 

A timing chain (or timing belt) connects the crankshaft to the camshafts. The shafts must be kept in sync so that the valves open and close at the correct point in the piston’s travel.

How Variable Valve Timing and Phasers Work

In a traditional engine, valve timing (when the valves open and close) is fixed. But with a modern VVT system, the position of the camshaft (s) can be adjusted, thereby altering valve timing. Having this ability can improve engine performance, increase fuel economy, or both. 

Several different components work together within a typical VVT system. Most vehicles use a hydraulically-operated phaser (aka actuator) located at the end of the camshaft to change the camshaft’s position and retard or advance valve timing.

An oil control solenoid (often referred to as a VVT solenoid), applies oil pressure to activate the phaser. The PCM controls the VVT solenoids based on input from various sensors.

Typically, there’s one VVT solenoid for each phaser. Some vehicles only have a phaser on the exhaust camshaft or the intake camshaft, while others have phasers on both.

It’s worth noting that different automakers have different naming conventions for their VVT systems. For example, Ford refers to its system as Twin Independent Variable Camshaft Timing (Ti-VCT) and BMW calls its setup VANOS.

What Happens When a Cam Phaser Goes Bad: Three Common Symptoms 

Cam phasers are a common issue on many modern vehicles. Ford, in particular, is well-known for having phaser problems on its gas-powered full-size trucks and SUVs.

If your vehicle’s cam phasers begin to fail, you’ll likely notice one or more of the following symptoms:

Illuminated Check Engine Light

Your car’s engine computer, which is often referred to as the powertrain control module (PCM), monitors the position of the camshaft (s) via one or more camshaft position sensors. If the module detects the camshaft has deviated from its expected position (due to a faulty phaser), the module will turn on the check engine light and store a diagnostic trouble code in its memory.

Poor Engine Performance

A malfunctioning phaser can prevent the valve timing from advancing or retarding as needed. As a result, the engine may exhibit performance problems, such as rough running and poor acceleration. 

Rattling Noise

Most phasers are designed to lock into position at base idle. But when a phaser fails, it may no longer lock into place, resulting in a rattling or knocking sound coming from the top-end of the engine. The noise is often most noticeable at idle when the engine is hot.

The video below demonstrates phaser noise in a Ford engine:

How Much Does it Cost to Replace Cam Phasers?

Replacing cam phasers is not cheap. You can expect to pay anywhere from $800 to $2500 to get the job done by a professional. Of course, the exact cost will depend on several factors, such as the year, make, and model of the vehicle.

If you have the know-how, you can save a lot of money by replacing the phasers yourself. CarParts.com has a wide selection of replacement cam phasers available for a variety of makes and models.

Products Mentioned in this Guide

Any information provided on this Website is for informational purposes only and is not intended to replace consultation with a professional mechanic. The accuracy and timeliness of the information may change from the time of publication.

How much does it cost to replace intake camshaft actuator?

Is it worth fixing a camshaft?

What does a camshaft actuator do in a car?

How long does it take to replace a camshaft sensor?