How to measure blood pressure at home without machine

To monitor your blood pressure using an automatic blood pressure monitor, find a comfortable place to sit with good back support at a table or desk.

Table of Contents Show

From Mayo Clinic to your inbox
Advertisement
Tips for Checking Your Own Blood Pressure
Before Checking Your Blood Pressure
Step-by-Step Blood Pressure Check
How do you check your blood pressure with your fingers?
How can I check my blood pressure at home manually?
Is there another way to measure blood pressure?

When you're ready to take your blood pressure, sit quietly for three to five minutes beforehand.

Place your feet flat on the floor and rest your arm on a tabletop even with your heart. Lean against the back of the chair. Stretch out your arm, palm upward.

Place the cuff on your bare upper arm one inch above the bend of your elbow. Make sure the tubing falls over the front center of your arm so that the sensor is correctly placed. Pull the end of the cuff so that it's evenly tight around your arm. You should place it tight enough so that you can only slip two fingertips under the top edge of the cuff. Make sure your skin doesn't pinch when the cuff inflates.

To get started, wait a moment, then press start. Remain still and quiet as the machine begins measuring. The cuff will inflate, then slowly deflate so that the machine can take your measurement. When the reading is complete, the monitor displays your blood pressure and pulse on the digital panel. If the monitor doesn't record a reading, reposition the cuff and try again. Rest quietly and wait about one to two minutes before taking another measurement.

Record your numbers, either by writing the information down or by entering the information into an electronic personal health record. Some monitors can upload your blood pressure readings automatically into a computer or mobile device.

From Mayo Clinic to your inbox

Sign up for free, and stay up to date on research advancements, health tips and current health topics, like COVID-19, plus expertise on managing health.

To provide you with the most relevant and helpful information, and understand which information is beneficial, we may combine your email and website usage information with other information we have about you. If you are a Mayo Clinic patient, this could include protected health information. If we combine this information with your protected health information, we will treat all of that information as protected health information and will only use or disclose that information as set forth in our notice of privacy practices. You may opt-out of email communications at any time by clicking on the unsubscribe link in the e-mail.

Jan. 20, 2022

Symptoms, Diagnosis & Monitoring of High Blood Pressure. American Heart Association. http://www.heart.org/HEARTORG/Conditions/HighBloodPressure/SymptomsDiagnosisMonitoringofHighBloodPressure/Instructional-Video_UCM_303324_Article.jsp# Accessed Dec. 6, 2011.

Mayo Clinic does not endorse companies or products. Advertising revenue supports our not-for-profit mission.

Advertising & Sponsorship

Policy
Opportunities
Ad Choices

You don't always have to go to your doctor's office to have your blood pressure checked; you can monitor your own blood pressure at home. This is especially important if your doctor recommends that you monitor your blood pressure on a regular basis.

Tips for Checking Your Own Blood Pressure

There are certain factors that can cause blood pressure to temporarily rise. For example, blood pressure normally rises as a result of:

Stress
Smoking
Cold temperatures
Exercise
Caffeine
Certain medicines

Try to avoid as many of these factors as you can when taking your blood pressure. Also, try to measure your blood pressure at about the same time each day. Your doctor may want you to check your blood pressure several times during the day to see if it fluctuates.

Before Checking Your Blood Pressure

Find a quiet place to check your blood pressure. You will need to listen for your heartbeat.
Make sure that you are comfortable and relaxed with a recently emptied bladder (a full bladder may affect your reading).
Roll up the sleeve on your arm or remove any tight-sleeved clothing.
Rest in a chair next to a table for 5 to 10 minutes. Your arm should rest comfortably at heart level. Sit up straight with your back against the chair, legs uncrossed. Rest your forearm on the table with the palm of your hand facing up.

Step-by-Step Blood Pressure Check

If you purchase a manual or digital blood pressure monitor (sphygmomanometer), follow the instruction booklet carefully.

The following steps provide an overview of how to take your left arm blood pressure on either a manual or digital blood pressure monitor. Simply reverse the sides to take a blood pressure in your right arm.

1. Locate your pulse

Locate your pulse by lightly pressing your index and middle fingers slightly to the inside center of the bend of your elbow (where the brachial artery is). If you cannot locate your pulse, place the head of the stethoscope (on a manual monitor) or the arm cuff (on a digital monitor) in the same general area.

2. Secure the cuff

Slide the cuff onto your arm, making sure that the stethoscope head is over the artery (when using a manual monitor.) The cuff may be marked with an arrow to show the location of the stethoscope head. The lower edge of the cuff should be about 1 inch above the bend of your elbow. Use the fabric fastener to make the cuff snug, but not too tight.

Place the stethoscope in your ears. Tilt the ear pieces slightly forward to get the best sound.

3. Inflate and deflate the cuff

If you are using a manual monitor:

Hold the pressure gauge in your left hand and the bulb in your right.
Close the airflow valve on the bulb by turning the screw clockwise.
Inflate the cuff by squeezing the bulb with your right hand. You may hear your pulse in the stethoscope.
Watch the gauge. Keep inflating the cuff until the gauge reads about 30 points (mm Hg) above your expected systolic pressure. At this point, you should not hear your pulse in the stethoscope.
Keeping your eyes on the gauge, slowly release the pressure in the cuff by opening the airflow valve counterclockwise. The gauge should fall only 2 to 3 points with each heartbeat. (You may need to practice turning the valve slowly.)
Listen carefully for the first pulse beat. As soon as you hear it, note the reading on the gauge. This reading is your systolic pressure (the force of the blood against the artery walls as your heart beats).
Continue to slowly deflate the cuff.
Listen carefully until the sound disappears. As soon as you can no longer hear your pulse, note the reading on the gauge. This reading is your diastolic pressure (the blood pressure between heartbeats).
Allow the cuff to completely deflate.

You'll get the most accurate reading if your arm is held straight.

If you released the pressure too quickly or could not hear your pulse, DO NOT inflate the cuff again right away. Wait one minute before repeating the measurement. Start by reapplying the cuff.

If you are using a digital monitor:

Hold the bulb in your right hand.
Press the power button. All display symbols should appear briefly, followed by a zero. This indicates that the monitor is ready.
Inflate the cuff by squeezing the bulb with your right hand. If you have a monitor with automatic cuff inflation, press the start button.
Watch the gauge. Keep inflating the cuff until the gauge reads about 30 points (mm Hg) above your expected systolic pressure.
Sit quietly and watch the monitor. Pressure readings will be displayed on the screen. For some devices, values may appear on the left, then on the right.
Wait for a long beep. This means that the measurement is complete. Note the pressures on the display screen. Systolic pressure (the force of the blood against the artery walls as your heart beats) appears on the left and diastolic pressure (the blood pressure between heartbeats) on the right. Your pulse rate may also be displayed in between or after this reading.
Allow the cuff to deflate.

If you did not get an accurate reading, DO NOT inflate the cuff again right away. Wait one minute before repeating the measurement. Start by reapplying the cuff.

4. Record your blood pressure.

Follow your doctor's instructions on when and how often you should measure your blood pressure. Record the date, time, systolic and diastolic pressures. You should also record any special circumstances like any recent exercise, meal, or stressful event.

At least once a year, and especially after you first purchase your blood pressure monitor, bring your monitor with you to your doctor's visit to check the machine’s accuracy. This is done by comparing a blood pressure reading from your machine with one from the doctor's office machine.

How do you check your blood pressure with your fingers?

Place the fingers on the inside of the wrist to locate the pulse. Now, take two fingers (preferably index and middle fingers) and place them just below the wrist creases on the thumb side of the hand. A strong pulse felt at the wrist correlates to a systolic blood pressure of at least 80 mmHg.

How can I check my blood pressure at home manually?

To begin, place the cuff on your bare upper arm one inch above the bend of your elbow. Pull the end of the cuff so that it's evenly tight around your arm. You should place it tight enough so that you can only slip two fingertips under the top edge of the cuff. Make sure your skin doesn't pinch when the cuff inflates.

Is there another way to measure blood pressure?

Another method to obtain BP measurements from the wrist with a smartwatch is through arterial tonometry (Figure 2). Arterial tonometry utilizes the concept of arterial wall applanation to measure the arterial BP waveform.