Location of oil pressure sensor?
 Show 23239 13 2000 TJ 4.0l 3spd auto. Went wheeling last night and noticed this morning when I start the jeep the gauge goes straight to 80 and doesn't move at all, acceleration or deceleration, nothing. Hoping it's just the sensor? Can anyone point me in the direction of where it is? I saw a few pics online but doesn't seem like I can locate it. Also, any other culprits this may be? Joined
Nov 26, 2005 · 50,403 Posts
It's next to the oil filter, it has a wiring harness connected to it. Joined
May 8, 2013 · 736 Posts
Discussion Starter · #3 ·
Oct 25, 2014 It's next to the oil filter, it has a wiring harness connected to it. thank you, does this sound like what it may be or should I be on the lookout for something else too Joined Sep 29, 2014 · 19 Posts
Turn the key without starting it, If it pegs, turn the key off and unplug the sensor. Turn the key without starting and if it doesn't peg, it's 99.99% chance the sending unit is bad. Joined May 8, 2013 · 736 Posts
Discussion Starter · #5 · Oct 25, 2014 Turn the key without starting it, If it pegs, turn the key off and unplug the sensor. Turn the key without starting and if it doesn't peg, it's 99.99% chance the sending unit is bad. before I go unplugging stuff is this the sensor? 109.3 KB Views: 1,025 Joined May 8, 2013 · 736 Posts
Discussion Starter · #6 · Oct 25, 2014 Better pic 130.1 KB Views: 1,025 Joined Nov 26, 2005 · 50,403 Posts
No, that is the camshaft position sensor. Give me a minute or two and I'll post a photo of the oil pressure sender... Joined May 8, 2013 · 736 Posts
Discussion Starter · #8 · Oct 25, 2014 Turn the key without starting it, If it pegs, turn the key off and unplug the sensor. Turn the key without starting and if it doesn't peg, it's 99.99% chance the sending unit is bad. found the sensor, did this and those were the symptoms. Connected it pegged, disconnected didn't move. I'll be replacing the
sensor tomorrow Joined Nov 26, 2005 · 50,403 Posts
Just found a pic...
Joined Sep 29, 2014 · 19 Posts
found the sensor, did this and those were the symptoms. Connected it pegged, disconnected didn't move. I'll be replacing the sensor tomorrow It's an easy job, sending unit costs around 50 bucks.
Joined Nov 26, 2005 · 50,403 Posts
One important note... don't waste your time or $$$ installing an aftermarket oil pressure sender from places like Autozone... they commonly have problems and are often junk. It took 3 from Autozone one Sunday before I got one for my son's car that worked properly. Get a Mopar sender from either the dealer's parts department or with a discount from
WeRMopar.com - OEM Parts For Chrysler, Dodge, Jeep, and Ram Vehicles Joined May 8, 2013 · 736 Posts
Discussion Starter · #12 · Oct 26, 2014 One important note... don't waste your time or $$$ installing an aftermarket oil pressure sender from places like Autozone... they commonly have problems and are often junk. It took 3 from Autozone one Sunday before I got one for my son's car that worked properly. Get a Mopar sender from either the dealer's parts department or with a
discount from WeRMopar.com - OEM Parts For Chrysler, Dodge, Jeep, and Ram Vehicles do I have to drain the oil to change this? Joined Nov 26, 2005 · 50,403 Posts
do I have to drain the oil to change this? No, at most a few drops of oil will come out. Spread a newspaper underneath which will be plenty. Joined Dec 19, 2011 · 768 Posts
I can afford to drive a jeep because of members who help. Thanks Jerry! Where are oil pressure sensors located?The oil pressure sensor is typically located near the bottom or side of an engine, between the oil filter and the oil pan.
How much does it cost to replace the oil pressure sensor in Jeep?The average cost for a Jeep Wrangler oil pressure sensor replacement is between $192 and $227. Labor costs are estimated between $132 and $167 while parts are priced at $60. This range does not include taxes and fees, and does not factor in your specific model year or unique location.
Can I drive with code P06DD?Can I still drive? No. Driving with an active P06DD code and an illuminated engine light isn't recommended. This code is related to low oil pressure, which, if left undiagnosed, could potentially damage critical moving parts of your engine.
|
2013 jeep wrangler oil pressure sensor location
Related Posts
Copyright © 2024 membukakan Inc.
